Tuesday, August 4, 2020

2nd Generation EV

     A Control board was developed for testing the power load draw of the vehicle. The basic component of the board consists of a motor controller, battery pack, DC/DC controller, and power sensors. For the supercapacitor module, a Maxwell 55 F 17 V device was used. A model remote-controlled car was used for simulation. Although the current rating is lower than actual electric vehicle, profile characteristics are similarly depicted, which allowed for insightful analysis of the proposed system. A vehicle without load weighs 20 kg and a vehicle with a load weighs 30 kg. The vehicle consists of a DC permanent magnet motor, which connects axles to all wheels with differentials. Figures 10 shows the image of the control board and the vehicle. There were two prototype development stage to build the control board.

Monday, August 3, 2020

Vehicle Design Circuitry

     Based on concept designs, the powertrain configuration was developed for vehicle test. The configuration can be largely divided into three sections: supercapacitor, battery pack, and traction motor. The supercapacitor is connected to a buck booster for constant desired voltage to the traction motor. In figure 9a, the supercapacitor is powering the traction motor. In figure 9b, the battery pack is powering the traction motor.



Thursday, July 30, 2020

Fuzzy Rules

     The first input variable is the peak current in Amps (A). The input is calculated with an array of values entering if/else function in Arduino to find maximum current value during the acceleration. The second input variable is the current slope measured in Amps per millisecond (A/ms). The current slope is the rate in which the current value decreases after founding peak current during acceleration. The algorithm takes the change in the current rating over 200 milliseconds and calculates the current slope.

    The output of the fuzzy controller is the current prediction, which will be used with voltage to predict power. Rules were developed with the empirical evaluation of the DC motor current profile.





Monday, July 27, 2020

Sunday, July 26, 2020

Fuzzy Raw Code MATLAB

 [System]

Name='poweroutput'

Type='mamdani'

Version=2.0

NumInputs=2

NumOutputs=1

NumRules=25

AndMethod='min'

OrMethod='max'

ImpMethod='min'

AggMethod='max'

DefuzzMethod='centroid'


[Input1]

Name='Peak_Power'

Range=[50 100]

NumMFs=5

MF1='VLPP':'gaussmf',[5.308 50]

MF2='LPP':'gaussmf',[5.308 62.5]

MF3='MPP':'gaussmf',[5.308 75]

MF4='HPP':'gaussmf',[5.308 87.5]

MF5='VHPP':'gaussmf',[5.308 100]


[Input2]

Name='Power_Slope'

Range=[10 80]

NumMFs=5

MF1='VLPS':'gaussmf',[7.434 10]

MF2='LPS':'gaussmf',[7.434 27.5]

MF3='MPS':'gaussmf',[7.434 45]

MF4='HPS':'gaussmf',[7.434 62.5]

MF5='VHPS':'gaussmf',[7.434 80]


[Output1]

Name='Power_Rating'

Range=[20 60]

NumMFs=5

MF1='VL':'trimf',[10 20 30]

MF2='L':'trimf',[20 30 40]

MF3='M':'trimf',[30 40 50]

MF4='H':'trimf',[40 50 60]

MF5='VH':'trimf',[50 60 70]


[Rules]

5 5, 2 (1) : 1

1 1, 2 (1) : 1

3 3, 3 (1) : 1

5 1, 5 (1) : 1

4 1, 5 (1) : 1

4 2, 4 (1) : 1

4 5, 2 (1) : 1

5 4, 3 (1) : 1

5 3, 4 (1) : 1

5 2, 5 (1) : 1

5 1, 5 (1) : 1

3 3, 3 (1) : 1

3 2, 4 (1) : 1

3 4, 3 (1) : 1

3 5, 2 (1) : 1

1 5, 1 (1) : 1

1 4, 1 (1) : 1

1 3, 2 (1) : 1

1 2, 3 (1) : 1

1 1, 3 (1) : 1

2 5, 2 (1) : 1

2 4, 2 (1) : 1

2 3, 3 (1) : 1

2 2, 4 (1) : 1

2 1, 4 (1) : 1


Wednesday, July 15, 2020

Fuzzy Build

     The vehicle power rating is dynamic due to vehicle weight and must be calculated during acceleration. To predict I vehicle, the fuzzy logic rule-based algorithm is used. Based on the peak current rating and the current slope, the algorithm will determine the current threshold. The general rule of the fuzzy logic is shown below.

1.    Heavier vehicles consist of higher peak current.

2.    Faster accelerations result in higher peak current.

3.    Faster accelerations result in higher current slope.   

     The reason why current threshold values cannot be determined from the peak current itself is due to the acceleration profile. In comparison, a lighter vehicle with faster acceleration can have the same peak current as a heavy vehicle with lower acceleration. By introducing the current slope, which looks at the difference in the current value over a certain period of time, the fuzzy logic value will be closer to the average vehicle current rating.



Tuesday, July 14, 2020

MATLAB Simulation

     The algorithm will focus on vehicle acceleration from this point because the regenerative braking method is simple: power from the motor goes to the supercapacitor based on the supercapacitor SoC status. Also, comprehensive SoC status-based concepts have already been well established. However, because the powertrain in this research deals with vehicles with varying weight loads, the power and current profiles are different for different load weights. Therefore, the algorithm cannot rely on the same power threshold variables used in previous equations during the vehicle acceleration.

     MATLAB Simulink simulation of a 24 V electric vehicle powertrain with DC permanent motor was performed to contrast the vehicle speed and power during different load. A vehicle with no load weighs and a vehicle with additional load. The vehicle system was designed to match the vehicle for the driving test. Included are the battery pack subsystem, PWM, gearbox, differential, and vehicle body with appropriate variables. 




        A vehicle with no load achieves desiring speed in 1.4 seconds while the vehicle with load takes 5.7 seconds. The peak current and driving current for the loaded vehicle is higher with 285 A and 167 A respectively while vehicle with no load shows 247 A and 89 A for peak current and driving current, respectively.

     Graphs show vehicles with different loads take different acceleration time and current ratings. Higher load vehicle takes longer time to reach full speed (lower slope in power profile) and start with higher current ratings. The algorithm must take account of the changing vehicle current rating and acceleration time for the supercapacitor to successfully perform optimal discharge during vehicle acceleration.



2nd Generation EV

     A Control board was developed for testing the power load draw of the vehicle. The basic component of the board consists of a motor cont...